win a ball from Bowling.com

Author Topic: Abralon Pad Life  (Read 8437 times)

Norm3v

  • Full Member
  • ***
  • Posts: 178
Abralon Pad Life
« on: October 27, 2010, 04:59:29 PM »
Hey everyone, sorry if this topic has been posted before but I couldn't find it on here.

Do you guys know the average life expectancy of an Abralon pad? Any tips to cleaning them or prolonging their desired cut? I just bought a spinner and I heard they dont last much past 6 balls, and now I can see why. My pro shop guy said to always count how many times you use it, and I was thinking of taking that a step further and putting a marker mark on them for every time used. Do you guys clean them in water and/or soapy water to get the grime out? I dont want to use a 500 pad thats actually a 1000, 2000 thats actually a 4000, etc. etc.

 

adcwsdad

  • Jr. Member
  • **
  • Posts: 6
Re: Abralon Pad Life
« Reply #1 on: November 13, 2010, 09:22:16 PM »
Your pro shop guy is right. Keep track of the number of uses for each pad. I use a Sharpie. Wet sanding provides lubrication and helps to keeep your Abralon pads fresher. As far as wet sanding, I tried the Smart Pro from Polish Your Ball (www.polishyourball.com). It works great with my ball spinner. Just a few sprays of water with a squirt bottle was all that was needed. This helped to cut down on splatter to virtually nothing. I found that my pads last longer than by just holding the pads in my hand. Plus I was able to acheive a more consistent finish also. Hint the higher the # grit of the Abralon, the smaller the amount water that is needed for wet sanding.

cosmo

  • Sr. Member
  • ****
  • Posts: 324
Re: Abralon Pad Life
« Reply #2 on: March 16, 2011, 08:48:48 AM »
 
As a follow up to this, as these pads are used do they "transistion" towards higher # grits? 
do the 1000 eventually become closer to 2000 and 2000-> 4000?
 
 
 



         got mule?
Where's my Mule?

charlest

  • Hero Member
  • *****
  • Posts: 24523
Re: Abralon Pad Life
« Reply #3 on: March 16, 2011, 07:47:31 PM »
In general, yes.
 
cosmo wrote on 3/16/2011 8:48 AM:
 
As a follow up to this, as these pads are used do they "transistion" towards higher # grits? 
do the 1000 eventually become closer to 2000 and 2000-> 4000?
 
 
 



         got mule?


"None are so blind as those who will not see."
"Some bowlers are crazy as pickled cats."
 
"None are so blind as those who will not see."

DukeHarding

  • Hero Member
  • *****
  • Posts: 5855
Re: Abralon Pad Life
« Reply #4 on: March 17, 2011, 10:00:44 AM »
Yes,they do.
I buy used Abralon pads from a pro shop...500 is 1000, 1000 grit is 2000, 2000 is 4000, etc. You can develop a feel for the grit and come pretty close to what you want.
I use Green Scotch Brite, then 1000 (which is 2000) on all my equipment. Rarely use 4000 grit...I rarely use polish, being a lefty.
cosmo wrote on 3/16/2011 8:48 AM:
 
As a follow up to this, as these pads are used do they "transistion" towards higher # grits? 
do the 1000 eventually become closer to 2000 and 2000-> 4000?
 
 
 



         got mule?


Duke Harding


azguy

  • Hero Member
  • *****
  • Posts: 8364
Re: Abralon Pad Life
« Reply #5 on: May 22, 2011, 06:34:13 AM »
Not a hard and fast rule but I use a pad normally 4-6 times depending on the grit and then I mark it as the next grit 'finer'. If you plan on using them I'd suggest getting a small nail brush, kmart/walmart/target, and I scrub them after each side of the ball. Just rinsing them in water will not loosen all the "ball material" off the pad.  A sharpie will not come off in the water so I use that to mark the pad.

 

I'm also cheap. Once the pad is past it's life, I turn it over and if a polish is needed then I'll use the pad side to apply it. Again, I'm cheap so I'll try to use them as long as I can for doing jobs that need to be done. It's a 'feel thing' but U use a worn out 2000 with cleaner ( VERY light pressure) and it takes off all marks and cleans very good. LIGHT pressure or you'll change the grit.

 

Hope this helps.



If you don't want my opinion, don't ask. If you don't like my opinion, ignore my posts. Have A Nice Day .



T C 300

  • Hero Member
  • *****
  • Posts: 550
Re: Abralon Pad Life
« Reply #6 on: May 22, 2011, 08:42:01 PM »
the first few times ( 5 ish), you can tell your cutting into the ball pretty good....
 
after that its not the same... i still use those pads "by hand" and get great results....
i have went back to sand paper for when i need to cut into the ball bit, then go to ab 
even sandpaper works pretty good by hand!!  dont rub to hard...  lol