win a ball from Bowling.com

Author Topic: Router depth  (Read 3670 times)

mbrown205

  • Sr. Member
  • ****
  • Posts: 278
Router depth
« on: August 19, 2014, 05:35:14 PM »
What's the best depth for using a router for plug cutting? Also would you recommend resurfacing after cutting plug, or just sanding on a ball spinner?

 

itsallaboutme

  • Hero Member
  • *****
  • Posts: 2001
Re: Router depth
« Reply #1 on: August 19, 2014, 05:54:12 PM »
You need to adjust the router depth on every ball.  Resurfacing is up to you.

JohnP

  • Hero Member
  • *****
  • Posts: 5819
Re: Router depth
« Reply #2 on: August 20, 2014, 05:04:58 PM »
I assume you're using the router with a shield.  I adjust mine for each ball by setting the bit height so I can see just a sliver of light between the bit and the ball.  Be sure the setting doesn't change when you lock the bit down.  --  JohnP

mbrown205

  • Sr. Member
  • ****
  • Posts: 278
Re: Router depth
« Reply #3 on: August 20, 2014, 05:10:22 PM »
The shield is what the vacuum hooks up to correct?

JohnP

  • Hero Member
  • *****
  • Posts: 5819
Re: Router depth
« Reply #4 on: August 21, 2014, 04:33:24 PM »
Yes, it's made out of clear plastic or plexiglass.  --  JohnP

Rightycomplex

  • Hero Member
  • *****
  • Posts: 1250
Re: Router depth
« Reply #5 on: August 22, 2014, 10:07:24 AM »
It is best to have a plug cutter. Every ball is different. On my press, even at 0-0, some balls will be off so adjust accordingly. I take the cutter to the ball and adjust the table so that there are no gaps.

When using a router, which I have very little experience with, I texted it the same as the plug cutter, adjusting from ball to ball. Resurfacing is the choice of the bowler. I use grill screen to clean up the plug work and have a set of abralon pads to smooth out the work. I'll then take the ball to box.
James C. Jones
Orbdrillers Pro Shop Holiday Bowl
Chester, Va.

Hammer Regional/Amateur Staff Member

www.facebook.com/orbdrillers
Orbdrillers.com
Hammerbowling.com

EFFEN 10

  • Sr. Member
  • ****
  • Posts: 341
Re: Router depth
« Reply #6 on: August 22, 2014, 07:31:40 PM »
It is best to have a plug cutter. Every ball is different. On my press, even at 0-0, some balls will be off so adjust accordingly. I take the cutter to the ball and adjust the table so that there are no gaps.

X2. I also use my plug cutter to zero my table. I check it every couple of weeks.
The more I practice,the luckier I get.

itsallaboutme

  • Hero Member
  • *****
  • Posts: 2001
Re: Router depth
« Reply #7 on: August 22, 2014, 09:23:46 PM »
There is no reason to go out and buy a plug cutter if you don't have one and you have a router.  You can do all the plug work you need to do with a router. 

Rightycomplex

  • Hero Member
  • *****
  • Posts: 1250
Re: Router depth
« Reply #8 on: August 22, 2014, 09:28:57 PM »
There is no reason to go out and buy a plug cutter if you don't have one and you have a router.  You can do all the plug work you need to do with a router.

True. I just said it's best to have one. Saves time, energy, and effort. I can cut down a fully plugged ball in a matter of a couple seconds and have it surfaced and ready for drilling in 2 mins. A plug cutter can pay for itself in 2 nights in the shop but that's just depends on how hard you want to work and how much time you want to save. Some guys get really good at using a router, I'm not one.
James C. Jones
Orbdrillers Pro Shop Holiday Bowl
Chester, Va.

Hammer Regional/Amateur Staff Member

www.facebook.com/orbdrillers
Orbdrillers.com
Hammerbowling.com

JohnP

  • Hero Member
  • *****
  • Posts: 5819
Re: Router depth
« Reply #9 on: August 23, 2014, 08:31:15 PM »
I would love to be able to use a plug cutter but the shroud on my sidewinder isn't big enough for one.  I have one I bought used without realizing I couldn't use it.  If anyone is interested, it has a MT 2 shaft (you can buy an adapter to straight shaft), doesn't look like it's ever been used, and I'll sell it for $50 + actual shipping cost.  PM me if interested.  --  JohnP