win a ball from Bowling.com

Author Topic: Anyone know where I can pick up...  (Read 1765 times)

JessN16

  • Hero Member
  • *****
  • Posts: 3716
Anyone know where I can pick up...
« on: September 23, 2009, 08:24:09 PM »
...a 16-pound Break Pearl or Break Point Pearl long-pin ball? I'm specifically looking for something in the 5-inch pin-to-CG and about 6- to 7-inch pin-to-MB range, with the CG reasonably in line. I've found some 15-pounders with those stats but no 16s.

I'm looking for NIB, but I'm not looking to break the bank just to get these specs. I have a drilling experiment I want to undertake.

Jess

 

surface_solutions

  • Sr. Member
  • ****
  • Posts: 408
Re: Anyone know where I can pick up...
« Reply #1 on: September 24, 2009, 04:33:17 AM »
I don't know for sure, but Tekneek seems to have long pin seconds all the time.  If he doesn't have them to ship today chances are he can have one drop shipped from the factory to you.  

I have purchased a few balls from him and he is a great person to deal with and prices are very fair also.  Check the feed back section lower in the forum if you have any questions.
--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com

tekneek

  • Hero Member
  • *****
  • Posts: 5657
Re: Anyone know where I can pick up...
« Reply #2 on: September 24, 2009, 07:56:57 AM »
Jess check your PM's
--------------------
Steve
Leading Edge Pro Shop
steve@leadingedgeproshop.net
512-755-2947
 
http://stores.shop.ebay.com/Leading-Edge-Pro-Shop__W0QQ_armrsZ1


Steve
Leading Edge Pro Shop
Radical Bowling Technologies Advisory Staff
brinkley2223@yahoo.com
512-755-2947

JessN16

  • Hero Member
  • *****
  • Posts: 3716
Re: Anyone know where I can pick up...
« Reply #3 on: September 24, 2009, 01:28:16 PM »
quote:
Jess check your PM's
--------------------
Steve
Leading Edge Pro Shop
steve@leadingedgeproshop.net
512-755-2947
 
http://stores.shop.ebay.com/Leading-Edge-Pro-Shop__W0QQ_armrsZ1





pm'ed you back. Thanks for the quick response!

Jess

tekneek

  • Hero Member
  • *****
  • Posts: 5657
Re: Anyone know where I can pick up...
« Reply #4 on: September 24, 2009, 01:47:16 PM »
you bet my pleasure !!
--------------------
Steve
Leading Edge Pro Shop
steve@leadingedgeproshop.net
512-755-2947
 
http://stores.shop.ebay.com/Leading-Edge-Pro-Shop__W0QQ_armrsZ1


Steve
Leading Edge Pro Shop
Radical Bowling Technologies Advisory Staff
brinkley2223@yahoo.com
512-755-2947

minimum bob

  • Hero Member
  • *****
  • Posts: 519
Re: Anyone know where I can pick up...
« Reply #5 on: September 24, 2009, 06:35:18 PM »
quote:
...and about 6- to 7-inch pin-to-MB range...


I may be wrong, but isn't MB always 6.75" from the pin...?


--------------------
My ball speed is 14 MPH...and I'm speed dominant....

JessN16

  • Hero Member
  • *****
  • Posts: 3716
Re: Anyone know where I can pick up...
« Reply #6 on: September 24, 2009, 07:51:33 PM »
quote:
quote:
...and about 6- to 7-inch pin-to-MB range...


I may be wrong, but isn't MB always 6.75" from the pin...?


--------------------
My ball speed is 14 MPH...and I'm speed dominant....


Just wanted to guard against mis-marked or otherwise blem-type MBs. I have an Nkryption Code where the MB was about 5 inches from the pin and swung all the way around to 10 o'clock. Worked out fine for me because I used a Girard drill on the ball (and the MB ended up in the thumb-positive quadrant) but I didn't want that to be the case with this ball.

Jess

surface_solutions

  • Sr. Member
  • ****
  • Posts: 408
Re: Anyone know where I can pick up...
« Reply #7 on: September 25, 2009, 04:59:18 AM »
The best ball I ever owned was a blem N'code.  It had a mismarked MB, I just scaled the ball to verify true weights (locations on markings) and drilled from there.

I can't say enough about it.  It was just like a first quality ball.

But yes, MB is 6 3/4" from pin...
--------------------
(616) 690-0590
surface_solutions_proshop@yahoo.com