win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Wrath Dead Flush Q.  (Read 3323 times)

Matt Fortney

  • Hero Member
  • *****
  • Posts: 2423
Wrath Dead Flush Q.
« on: February 12, 2008, 01:18:08 PM »
I'm thinking about getting this ball for my wife, and we're getting to fill a gap UNDER a ball she has right now...the Zone Classic. The ZC is drilled pretty strong 4 X 45*, pin down. So my question is this, if we drill this thing with a 5" pin to PAP, and have the pin up, will it hook less overall? She's looking for a little less overall, and more of a skid/snap look. Might sound like a dumb question i guess, but so many times I've tried to fit a ball UNDER something, and the thing hooks too much. let me know. thanks.

Matt
--------------------
Hammer Pride Staff Member

http://www.hammerbowling.com
http://www.hammerstuff.com

"Nothing Hits Like A Hammer"
Logged

 

themachine300

  • Hero Member
  • *****
  • Posts: 1410
Re: Wrath Dead Flush Q.
« Reply #1 on: February 12, 2008, 09:41:23 PM »
Its kinda hard to say really.  I drilled alot of the newer Brunswick Zone balls, Classic, Vapor, Strike, Red, and I currently have the Wrath HF.  The Wrath HF is very strong, similar to what my Vapor Zone was.  I have not thrown the DF but I have seen it by two other people. IMO, it would be too strong, even with the weaker drill, as it doesn't look that much weaker than the HF.  I would do what you want in terms of a skid/flip, but again, IMO, it would overlap.
--------------------
www.bowlingsolutions.com

Move left, hook it more.....

Tommy Jones is a Gamecock fan...are you???

We shall now refer a 4-bagger as a hambone...Mark it down the revolution has started!

Edited on 2/12/2008 10:46 PM

Edited on 2/14/2008 9:09 PM
Logged
Philipp Hudak
Ebonite Amateur Staff
Bowl To Win!
#TeamEBI

Matt Fortney

  • Hero Member
  • *****
  • Posts: 2423
Re: Wrath Dead Flush Q.
« Reply #2 on: February 13, 2008, 02:07:20 PM »
thank you. i appreciate the reply!

Matt
--------------------
Hammer Pride Staff Member

http://www.hammerbowling.com
http://www.hammerstuff.com

"Nothing Hits Like A Hammer"
Logged

mrbowlingnut

  • Hero Member
  • *****
  • Posts: 5727
Re: Wrath Dead Flush Q.
« Reply #3 on: February 13, 2008, 02:40:23 PM »
I think it would be too strong i only have the HF myself, but i do have a classic zone and i think a few of the following would work well.

Jolt Pearl

Neptune

Avalanche solid or pearl

That is current stuff that will work or even a weak drilled uranium hrg at least 5 inch pin to pap
Logged

justdale

  • Hero Member
  • *****
  • Posts: 1879
Re: Wrath Dead Flush Q.
« Reply #4 on: February 13, 2008, 04:22:34 PM »
I have both the Wrath High Flush, and the Wrath Dead Flush, and IMO the Dead Flush is stronger then the High Flush. But make sure you drill it pin above fingers to give it the length you want
--------------------
Dale Williams
Columbia 300 Utah Amateur Staff
Logged

Hamburglar

  • Hero Member
  • *****
  • Posts: 804
Re: Wrath Dead Flush Q.
« Reply #5 on: February 13, 2008, 04:29:43 PM »
quote:
I have both the Wrath High Flush, and the Wrath Dead Flush, and IMO the Dead Flush is stronger then the High Flush. But make sure you drill it pin above fingers to give it the length you want
--------------------
Dale Williams
Columbia 300 Utah Amateur Staff


DF stronger than the HF???  WOW! 'cause my HF is a lot stronger than I expected it to be...

I guess my next step down will be a Jazz then...
--------------------
That which doesn't kill you will only make you stronger, that which doesn't make you stronger is a waste of time!
Logged

mattriley50

  • Newbie
  • *
  • Posts: 3
Re: Wrath Dead Flush Q.
« Reply #6 on: February 13, 2008, 08:24:54 PM »
i have my Dead flush drilled with the pin above the big finger and CG in the middle, nearly drilled for a lefty. I am a high rev player and ball speed of 17mph howevr this thing does not hook, do u think i may have a dud i got it for dryer lanes but this thing doesnt move
--------------------
columbia 300
QubicaAMF Staff member Australia

Edited on 2/13/2008 11:13 PM
Logged

urbanshaft

  • Hero Member
  • *****
  • Posts: 814
Re: Wrath Dead Flush Q.
« Reply #7 on: February 13, 2008, 09:11:28 PM »
on dry a high rev player could hook a spare ball.
very weird
Logged

justdale

  • Hero Member
  • *****
  • Posts: 1879
Re: Wrath Dead Flush Q.
« Reply #8 on: February 13, 2008, 09:40:49 PM »
I drilled mine 4 x 4 with a 1 1/2 in pin buffer, mine definitely out hooks my High Flush
--------------------
Dale Williams
Columbia 300 Utah Amateur Staff
Logged

Hamburglar

  • Hero Member
  • *****
  • Posts: 804
Re: Wrath Dead Flush Q.
« Reply #9 on: February 14, 2008, 01:24:53 PM »
quote:
i have my Dead flush drilled with the pin above the big finger and CG in the middle, nearly drilled for a lefty. I am a high rev player and ball speed of 17mph howevr this thing does not hook, do u think i may have a dud i got it for dryer lanes but this thing doesnt move
--------------------
columbia 300
QubicaAMF Staff member Australia

Edited on 2/13/2008 11:13 PM


Depends.  What's you PAP?  If you are a high tracker, you may have the pin too far away and thus, no hook.
--------------------
That which doesn't kill you will only make you stronger, that which doesn't make you stronger is a waste of time!
Logged

mattriley50

  • Newbie
  • *
  • Posts: 3
Re: Wrath Dead Flush Q.
« Reply #10 on: February 14, 2008, 02:54:05 PM »
i have around a 5 inch axis tilt

rev rate or around 540
--------------------
columbia 300
QubicaAMF Staff member Australia
Logged
Pages: [1]
« previous next »