win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: needs some tip plugging ball  (Read 1635 times)

Bluff

  • Hero Member
  • *****
  • Posts: 1011
needs some tip plugging ball
« on: September 08, 2009, 06:23:23 AM »
I am trying to plug some balls and have some boubble problems. whats easiest way to get around it ?

I got Ultimate 1 hour Plugs and Have try Pro-choice 6 hours.

both seems to boubble alot on me I am mixing it in fig 8 for 1m and 5m for 6 hour.

Anyhelp?
Logged

 

slashrr69

  • Hero Member
  • *****
  • Posts: 1266
Re: needs some tip plugging ball
« Reply #1 on: September 08, 2009, 03:30:04 PM »
try mixing it slower.. I was told the same thing when first starting using plug.. you might be srirring to quickly..
Logged

Cobalt Bomb

  • Hero Member
  • *****
  • Posts: 2053
Re: needs some tip plugging ball
« Reply #2 on: September 08, 2009, 04:43:17 PM »
I agree with above. Also, if you are using Ultimate, make sure it is fresh(less than 1 yr old.
If I have the time, I have good success with the Ebonite Powerhouse Everclear, I almost never get any bubbles with that.
Logged

qstick777

  • Hero Member
  • *****
  • Posts: 5188
Re: needs some tip plugging ball
« Reply #3 on: September 08, 2009, 06:03:53 PM »
I agree with all of the above - mixing thoroughly does not mean mix vigorously.  I learned that after a few times!

Also, I've been told you can tap the ball with a mallet to help bring the air bubbles to the top.  Since you are going to over pour and trim off the excess, the air bubbles at the top won't really matter.  Not sure how well that works with the 1 hour plug - I know you don't have much time before it starts to set up.

I've also heard that you can pop the air bubbles with a toothpick.

Logged

Bluff

  • Hero Member
  • *****
  • Posts: 1011
Re: needs some tip plugging ball
« Reply #4 on: September 09, 2009, 01:17:02 AM »
ok thanks for all the tip and will give it a try.

Yea is Ultimate Wizzard can't mix for longer than 1 m or is be harden b4 I pure it. I mix untill I feel the hit and I pure it like around 1 m or so.

I did kind of mixing it fast. I try it slow and see
Logged

mw11x300

  • Full Member
  • ***
  • Posts: 223
Re: needs some tip plugging ball
« Reply #5 on: September 09, 2009, 07:43:20 AM »
I've used Wizard for a long time now and one of the best things to do is take a lighter or a match and go over the top of the plug with the open flame.  This usually brings the air bubbles to the top and bursts them on contact.  I never have issues with air bubbles doing it this way.  Also make sure you pour the plug down the side of the hole slowly.
Logged

azguy

  • Hero Member
  • *****
  • Posts: 8364
Re: needs some tip plugging ball
« Reply #6 on: September 09, 2009, 07:51:54 AM »
I only use Tech Line or Power House plug but there has been times I mix to fast, have bubbles in the cup, I just don't take the time, my fault. To solve the bubble problem I put the ball under a 40 watt light, let the light stay on for about 20-30 minutes. It heats up the material, air bubbles come to the top and 'pop' (?) anyway they are gone and I haven't had any problems since.

In mixing material, as the old saying goes....speed kills.

The light thing also helps in the winter time if your area gets a bit cold at night. I had my heater go out last winter ( our really only super cold night for us ) and the light helped it stay warm along with getting the air bubbles out.
--------------------
az guy aka: R & L Bowlers Pro
  rlbowlerspro@cox.net



Logged

Bluff

  • Hero Member
  • *****
  • Posts: 1011
Re: needs some tip plugging ball
« Reply #7 on: September 10, 2009, 11:49:37 AM »
update

thanks guys I was mixing chem too fast. I slow down and was able to get good results

azguy thanks for light bulb tip where I am at is too hot I actually have to turn a/c on to keep room kwel for less bubble
Logged
Pages: [1]
« previous next »