BallReviews

General Category => Miscellaneous => Topic started by: Goof1073 on July 25, 2006, 07:46:23 AM

Title: Controling Resurfaced Backends...???
Post by: Goof1073 on July 25, 2006, 07:46:23 AM

It's that time of the year again when my local center will put down a fresh finish coat on the wood backends.  Typically this isn't a huge deal as I mainly practice during the summer and it's on the THS.  This year I'm bowling in a summer Sport Shot League and as luck would have it we are bowling on a short pattern.  Now I remember just how badly the ball hooked on the fresh surface last year and that was with a longer pattern!!!

So I'm looking for ideas on what to do to combat what I'm going to see and maybe even a ball / drilling.  I was originally thinking of something strong / with some surface and a more end-over-end release and let the ball burn up.  However I was also thinking of a weaker ball like an Ice (which is getting dusty on the shop's wall anyways) with a 0-Degree layout and a little bit of surface.

Really...any help / ideas are welcome.
--------------------
-Chris: DJ's Pro Shop : Auburn, MA

Title: Re: Controling Resurfaced Backends...???
Post by: Strider on July 25, 2006, 05:07:10 PM

Sounds like you've got some good initial ideas.  Using as much surface as you can get through the heads will help soften the backends.  Urethane is a great option if one is available.  Shorter sport shots have a lot of free hook.  Learning how to control it is a big factor in scoring well.
--------------------
Penn State Proud

Ron Clifton's Bowling Tip Archive (http://"http://www.bowl4fun.com/ron/roncarchive.htm")

Title: Re: Controling Resurfaced Backends...???
Post by: MTFD24 on July 25, 2006, 05:10:22 PM

Have to agree with Strider about trying urethane too. Have had great sucess using an old Black Hammer (polished) when there is light oil and/or short oil with "flying backends".


--------------------
The Older We Get, The Better We Were
www.MTFD.com - a NY State Vol. Fire Department
www.BowlWNY.com - local & national stories by Joe Ciccone
http://www.FDracing.com The worlds fastest firemen in the origional Xtreme Games
24 is not my age, IQ, or bowling average, but my firematic number, at least I think that what it is

Title: Re: Controling Resurfaced Backends...???
Post by: jimensminger on July 25, 2006, 05:51:19 PM

yella-dot...

Title: Re: Controling Resurfaced Backends...???
Post by: Goof1073 on July 25, 2006, 08:19:00 PM

I had thought of a urethane ball as well...but I don't have one available to utilize, nor do we have one at the shop.

They are doing the lanes starting tomorrow so I will get a practice session in on Thurdays.  Even though it will be the house shot it should show me a few things.  Maybe I'll just take out an old plastic ball and sand it down.  I remember Ritchie Allen doing this a few years back at the T.O.C. and he had a GREAT look with it.
--------------------
-Chris: DJ's Pro Shop : Auburn, MA

Title: Re: Controling Resurfaced Backends...???
Post by: dizzyfugu on July 26, 2006, 02:42:27 AM

If you want control on the back end and you know that it will be half way clean, a ball with a label drilling is a very good option. Take any ball that might potentially match the lane condition and even put on a label leverage drilling. Very good mid lane reaction, revs up nicely, and much forward movement in the back end without over-hooking.

A Black Ice could be a good basic option. If you face longer oil, sanding the ball up to 800 grit will kepp it IMHO in play with a label drilling. Only carrydown can cause problems, because the ball needs some dry back end boards to finish with the label setup.
--------------------

DizzyFugu - Reporting from Germany
Team "X" website & more about me: http://web.mac.com/timlinked/iWeb/X/Thomas.html
"All that we see or seem, is but a dream within a dream..." - Edgar Allen Poe

Title: Re: Controling Resurfaced Backends...???
Post by: Goof1073 on July 27, 2006, 09:44:48 PM

Well the lanes were just done and I tried to bowl on them with the Summer-THS out and DHAMHN!!  Almost every ball that I tried was too strong.  Our house has synthetic heads with wood backends and when the ball hit the fresh shot surface it just wanted to go left.  I tried most of my weaker stuff and even a few balls with rolling drillings (135-degree or more)...best look I had was with my plastic ball and after that I could get an En-Lino Level 2 down lane if I killed the shot and really spun the ball.

I really wish that I still had my old urethane equipment...but at this point I'm thinking of drilling up a tropical storm with a 0-degree layout and the pin 6" away from my PAP.  If that doesn't work I'm throwing my plastic ball all night!!!
--------------------
-Chris: DJ's Pro Shop : Auburn, MA