win a ball from Bowling.com

Author Topic: What's this drilling?! I LOVE IT!  (Read 2178 times)

dev

  • Sr. Member
  • ****
  • Posts: 401
What's this drilling?! I LOVE IT!
« on: October 09, 2005, 02:23:51 PM »
I have a SSP, no idea what drilliig is this, (http://img.photobucket.com/albums/v472/dev86/Bowling/ssp2.jpg)

but the condition makes it goes long and snap hard. =)

if I apply this drilling on a RSX, is it gonna go as far as my SSP and snap even harder?

 

BOWLGNUT

  • Hero Member
  • *****
  • Posts: 573
Re: What's this drilling?! I LOVE IT!
« Reply #1 on: October 09, 2005, 10:32:34 PM »
It is stack leverage with pin above finger. If you put it on RSX that will give some length and snap.
I hate ten pins but love the game of bowling with just the right ball to take them out.

livespive

  • Hero Member
  • *****
  • Posts: 4819
Re: What's this drilling?! I LOVE IT!
« Reply #2 on: October 09, 2005, 10:40:59 PM »
depends,

if that hole is at your pap, then it looks more like a 4x4
--------------------
Eric T. Spivey, P.E.
 Visionary Test Staff Member
http://www.visionarybowling.com
http://www.maysbowlingandbilliards.com

shimozukawa

  • Full Member
  • ***
  • Posts: 145
Re: What's this drilling?! I LOVE IT!
« Reply #3 on: October 09, 2005, 10:48:43 PM »
Also, it matters if you're rh/lh, too.

Next Level PS

  • Hero Member
  • *****
  • Posts: 1874
Re: What's this drilling?! I LOVE IT!
« Reply #4 on: October 09, 2005, 10:52:34 PM »
forget about the layout, the SSP was a super sideways balls. all the SSP I seen and drilled all exploded on the back.
--------------------

www.nextlevelproshop.com

Next Level Proshop
Union, NJ

"THE BOWLERS WILL NOT BE DENIED"

www.lovedoublesonline.com

dev

  • Sr. Member
  • ****
  • Posts: 401
Re: What's this drilling?! I LOVE IT!
« Reply #5 on: October 09, 2005, 11:53:22 PM »
I need a drilling for length and snap for my RSX(coming) but i need it for heavier med or maybe heavy oil.


my SSP is already doing well or med, and sometimes too agresssive.

Leftyhi-trak

  • Hero Member
  • *****
  • Posts: 2288
Re: What's this drilling?! I LOVE IT!
« Reply #6 on: October 10, 2005, 05:56:03 PM »
Why you do  want a length drilling with snap for heavier oil patterns???

dev

  • Sr. Member
  • ****
  • Posts: 401
Re: What's this drilling?! I LOVE IT!
« Reply #7 on: October 10, 2005, 07:57:40 PM »
quote:
Why you do  want a length drilling with snap for heavier oil patterns???


snap usually comes with length to retain energy.. am i wrong??

dev

  • Sr. Member
  • ****
  • Posts: 401
Re: What's this drilling?! I LOVE IT!
« Reply #8 on: October 11, 2005, 12:15:33 PM »
er.. which drilling should I apply to my RSX so that it can cover 5 or more boards on the same condition as my SSP ? =)

I'm a stroker, med revs and speed. lefty

Edited on 10/12/2005 0:20 AM

Edited on 10/12/2005 0:21 AM

dev

  • Sr. Member
  • ****
  • Posts: 401
Re: What's this drilling?! I LOVE IT!
« Reply #9 on: October 12, 2005, 12:31:15 AM »
ttt

dev

  • Sr. Member
  • ****
  • Posts: 401
Re: What's this drilling?! I LOVE IT!
« Reply #10 on: October 12, 2005, 05:37:17 AM »
I intend to get RSX for this few reasons.

1. Polished surface - for length
2. Solid coverstock - for backend.

ii i don drill the ball for a sharp backend and length, wad for i get RSX! =)

dev

  • Sr. Member
  • ****
  • Posts: 401
Re: What's this drilling?! I LOVE IT!
« Reply #11 on: October 12, 2005, 06:05:39 AM »
quote:
Bring the pin to about 3.5" from your PAP. Move it downwards relative to the grip to below finger level. And personally id still leave the cg in a strong position, you'll need all the backend you can if the pattern is heavy and/or long. The RSX may also need a surface adjustment to provide you with more control.
--------------------
ROTO GRIP & STORM
at
www.rpsbowling.com - Get a Grip



RotoDave,

if i brought down the pin below the fingers, it would create a earlier roll, to prevent the ball from going too far, and the CG in strong position for the backend, right?

*sorry, im a noob! =)