Post by: chun914 on July 31, 2003, 08:27:36 PM
play on fresh medium lane...
please suggest a layout for maximum control....predictable backend...?
and have some lenght......
THANKS....
info inside my profile..
Edited on 8/1/2003 11:41 AM
Edited on 8/3/2003 11:14 PM
Post by: chun914 on August 02, 2003, 11:42:29 AM
here's some information
~17mph
Med rev
Low Track
PAP - 4 1/8 , 1/8 up
axis rotation 45 to 60 degree
are there something need to becarful for such a low track player ??
please help with a layout suggestion ....
easy to control , predictable powerful backend....
some more lenght...played on medium length&volume oil....
currently own a Icon 2 ... about 3 1/2 x 3
reaction Rev , pin over bridge and CG straight down..
and a AZO ~ 3 1/2 x 3 1/2
i want the ball's lenght fits between the icon2 & Rev ....and a controlled backend...
Post by: chun914 on August 03, 2003, 09:53:57 PM
this is 14lbs 6 oz..
2.75oz top
2.5 -3 pin..
i like to play around 1st and 3th arrow.
Post by: chun914 on August 04, 2003, 04:56:00 AM
i have no idea how to drill it ..where to put the pin and the mass bias...
fyi.. my span 4 1/16 x 4 1/16
with small thumb and finger......middle finger 19 . ring - 5
Edited on 8/4/2003 5:06 AM
Post by: JOE FALCO on August 04, 2003, 06:10:00 AM
--------------------
Hit them light and watch them fight
J O E - F A L C O
Post by: chun914 on August 04, 2003, 07:00:06 AM
wanna check the reply either i'm at office or home....
Post by: Jeffrevs on August 04, 2003, 07:26:48 AM
Roger must have been real busy on Friday for him not to see this. I was away also or I would have responded. I have a Pure Fuel, and mine is drilled with a 4 inch pin to pap, and the mass bias in my track. For me (high tracker) the balls core and cover give me good length. I've only thrown it on 2 conditions.
One was a SHORT sport shot and the other was a med-heavy (heavy heads) house shot on primarily wood lanes..(18 ft synthetic, the rest wood).
The ball is very clean thru the heads, but at the same time has nice mid lane and great recovery. This ball should just kill a fresh house shot right up the 7 board!!
With your low track, a 4 in pin to pap will do for you for length. Maximum control and predictable backend, I would put the mass bias on your VAL...or something like a 4x2.
Sit tight, Roger will chime in later.........
--------------------
JEFF
Just chimin' in !
Post by: Mustang Guy on August 04, 2003, 10:57:17 AM
Thanks,
--------------------
Roger Noordhoek
Technical & Customer
Services Manager
Roto Grip, Inc.
Post by: chun914 on August 04, 2003, 09:17:52 PM
if a balance hole is needed..where should i put it..what about the size and depth??
will post my review on this ball later.....
Post by: Jeffrevs on August 05, 2003, 07:25:51 AM
--------------------
JEFF
Just chimin' in !
Post by: chun914 on August 05, 2003, 11:27:42 AM
Post by: chun914 on August 08, 2003, 11:09:52 AM
wanna confirm if i draw it correctly...
pin below middle finger and the bridge...4 1/2 to PAP..
a 50 degree PAP to MB.....
the side weight and finger/thumb weight not over 1oz ?
in this case...does a balance hole still needed ?
Post by: Jeffrevs on August 08, 2003, 12:05:27 PM
quote:
not drilled the ball yet..
wanna confirm if i draw it correctly...
pin below middle finger and the bridge...4 1/2 to PAP..
a 50 degree PAP to MB.....
the side weight and finger/thumb weight not over 1oz ?
in this case...does a balance hole still needed ?
Not if you're within an ounce I dont' think??
--------------------
JEFF
Just chimin' in !
Post by: chun914 on August 08, 2003, 12:40:19 PM
Post by: Jeffrevs on August 08, 2003, 12:44:30 PM
You should ask this specific question on the "drillings" board....
--------------------
JEFF
Just chimin' in !
Post by: chun914 on August 11, 2003, 09:19:42 AM
drilled it today...
pin below middle finger..
ended with 7/8oz thumb and 7/8oz side weight..
no weight hole for now..
will test it one day later..
is it necessary to drill a balance hole ??
if yes,,,how ?