win a ball from Bowling.com

Author Topic: Eraser Boost  (Read 20440 times)

admin

  • Hero Member
  • *****
  • Posts: 1241
Eraser Boost
« on: December 31, 1969, 06:00:00 PM »
Coverstock: Solid Chrome CADMIUMâ„¢

Weight Block: Modified Thunderâ„¢ with Power Ballâ„¢ Technology

Ball Color: Grape/Navy Ball

Finish: 1500-grit Polished

Logos: Flying "S", Storm, Eraser Boost

Gyration: 2.570 (Medium-High)

Differential: .041 (Medium)

Durometer: 75-77 Rex D-scale

Track Flare: High (5”)

Ball Length: 6 on a scale of 1-10

Back End: 7 on a scale of 1-10

Recommended Lane Conditions: Medium to Heavier Volume / Medium to Long Oil Patterns

 

YeahHossNV

  • Hero Member
  • *****
  • Posts: 626
Re: Eraser Boost
« Reply #16 on: July 06, 2002, 03:20:08 AM »
i drilled this ball with the pin above the bridge. this ball has the perfect combination of roll, spin, and length. the ball has good hit and amazing carry(as a matter of fact i think i left only 1 ten pin with this ball in a whole month). this ball is amazing i absolutly love this ball. this ball is deffinately a 11 out of 10.

bowlwbj

  • Jr. Member
  • **
  • Posts: 8
Re: Eraser Boost
« Reply #17 on: July 29, 2002, 10:59:50 AM »
Purchased the Boost for a medium to med-heavy condition with carrydown.  Was using a Powerbolt for this but needed to replace it.  Put the same drilling on it as the PB.  Pin 1" from PAP and 1/2" above midline and cg 4" from PAP and 1" below midline.  I know a lot of people say this drilling is no good but I have had good success with it on carrydown or broken down conditions as long as there is some oil there.  Found the condition I wanted to try it on & pulled it out.  The ball in box condition did ok but was still a little skiddy in the carrydown.  Thought I would have to adjust the cover but I had to see for myself first.  Took the cover down to around 800 grit with a pad and that did it.  Ball rolls, then hard arcs into the hole with really good hitting power.  Thanks to Storm technical staff for replying to my questions.  These guys always have time to answer questions - I guess that's one reason they're climbing to the top so fast!

REVOLUTIONS PS

  • Sr. Member
  • ****
  • Posts: 397
Re: Eraser Boost
« Reply #18 on: August 11, 2002, 07:53:31 PM »
We tested only one Eraser Boost ball, we drilled it with the pin 2 1/4" from the p.a.p. and the c.g. 4 1/2" from the p.a.p.  This drill pattern required a weight hole which was 25/32 and placed one inch past the p.a.p.  We polished the out of the box shell to a high gloss using Ebonite's factory finish.  

Our tester was the same player we have referred to in most of our other reviews.  A stroker style who averages about 17 mph and between 19 and 21 revolutions.  We were bowling in our home house, AMF synthetic lanes conditioned using the Kegel Elite machine.  We bowled on two of the more common house patterns, the only difference being that one had more oil in the center of the lane.  Both patterns included dry back ends.

The promotional material that the Boost comes with indicates that it is medium to heavy oil ball.  We weren't able to test it on any lane with what we would consider ‘heavy' or long oil nor were we able to test it on very much carry-down.  What the Boost did for us was handle the fresh back ends with control that we rarely have seen before.  The drill pattern was surely a part of this but the Boost's back end reaction was so smooth and predictable it tamed the dry back ends with ease.  The carry was also somewhat surprising, although Storm equipment is known for it's exceptional hitting power we weren't expecting this kind of power at this price point.  We were using a Storm Trauma on lanes near by and the Boost carried as well as the Trauma did all day.  

We were getting a bit more flare than we were expecting from this layout, nearly four inches but that didn't seem to hurt the balls controllability, we never had any ball over react in the back end-even on shots that we threw out into the dry.  The Boost was sensitive to front end break down but no more so than most.  That front end sensitivity would also be a product of the pattern we used, surely a longer pin to p.a.p. distance would create more length.  We are curious as to what the back end reaction would be like on a longer pin to p.a.p. distace on this ball and when we drill one, we will post a second review.  Overall, the Boost is another ball that we have really liked especially for the money.  If you are a Storm fan or just need a ball that will carry the pins at a price that won't break the bank, this one is worth a good long look.  

If you have any questions regarding this or any other of our reviews, e-mail us at: proshop@bowlero.com

Pbowler45

  • Newbie
  • *
  • Posts: 1
Re: Eraser Boost
« Reply #19 on: August 24, 2002, 04:33:53 PM »
I got this ball just as it was released on the market by Storm.  This summer I bowled in a sport shot league with it and it was awesome!  It did more than I expected it to.  The ball moved more than any other ball I or anyone had.  It still while battleing through all the oil was still able to hit like a truck. It knocked out the rest of the competition . After the first four weeks of the league four or five others had the ball and scored very well with it.  This ball even scored for me when the lanes had very little oil and super backends.  Just added speed and kept throwing it. This ball is one of the best balls I have seen ever.

paulvoelker1957

  • Newbie
  • *
  • Posts: 1
Re: Eraser Boost
« Reply #20 on: August 29, 2002, 10:00:15 AM »

I'll start by saying this is the first Storm product I'ved ever used. I've been a Hammer fan for the better part of 20 years. I never complained about Hammer and was always competitive using a wide variety of Hammers. My problem has always been the lack of mistake room I had. Hammers din't open the lanes up  enough for me. When bowlers far less skilled or experienced scored well making huge mistakes and I had to make spares just hit my average I would get upset.

The Boost I bought has a pin 3.5 out with 3.2 top weight. I used the strongest reaction layout Storm provided, placing my pap 4.25 inches from the pin. This gave me 2.25 ounces of side weight and 3/4 finger weight befroe drilling. After drilling my finger wieght increased to 7/8 of an ounce and my weight hole was drilled on vertivle axis line on midline not in my pap which is about 1/2 inch lower. I used an 1 1/8 inch drill bit and drilled 3 inches deep. The final side weight is 3/4 of an ounce. I don't usually use this aggresive drilling but I need something for heavy oil and carry down.

I got 3 games of practice in, playing in around the 20 board crossing out to 6 and back to the pocket on a very dry lane condition and the Boost got through the heads well and recovered nicely with a very heavy and even arcing roll. If I missed inside I crossed over because of the dry lanes but if I missed outside the ball was stable enough to recover without over reacting.

The next day I had my last summer league match and I was excited knowing I would have fresh oil and clean back end. In practice I didn't hit the head pin once and the biggest baby in the league said the Boost was to much ball for me. The lane condition that night was the "great cry baby wall" with 60 units from 15 to 15, about 20 units by the time you got 10 and then it droped off to 3 units from 5 to the gutter. The length of oil was out around 42 feet with squeaky clean backends.

I played around 15 with my break point around 7 and down the lane 52 feet. The Boost reacted evenly with tremendous roll and predictabilty. My first game was 300 followed by 246 and dropped off to 222. So much for being to much ball. My series would have been higher if I didn't have 2 big split and miss 2-10 pins and chopped a 3-6-9-10. The 2 splits were shots 6 board left of my target, the chop was 3 boards left and the 10 pins I left were on shots I over turned and threw to hard. All, not the ball's or the lane condition's fault.

I bowled in my fall league start just 8 days latter and shot 300-224-212. The reason for the drop off again was operated related and not adjusting quick enough on the changing lane conditions. Even when I made a mistake in targeting or speed the Boost was predictable and hard hitting. This ball has opened up the lanes for me and I expect a good season. I bought a second Boost and I will drill it with Storm's dry lane reaction layout which should improve my 2nd and 3rd game scores, less brain cramp shots.

The final chapter on this ball is:
1. Even rolling
2. Heavy end over end roll
3. Predictable break point
4. User friendly
5. Affordable
6. The hardest hitting ball I ever used
7. Good enough to buy 2

YeahHossNV

  • Hero Member
  • *****
  • Posts: 626
Re: Eraser Boost
« Reply #21 on: September 01, 2002, 02:56:36 PM »
well now that i decided i needed to back to 15lb equipment i had to buy another boost and i drilled it with the pin under the ring finger and the cg an inch and a half below it. lets start out by saying i loved this ball before and i love it even more now. the ball arcs slightly through the heads and midlane  and in the backend it makes a strong arcing turn and tears the pocket apart and it carries every pin perfectly. this ball takes on carry down without a problem. this ball would prefer a bowler with some hand but it should react ok for others. i give the ball a 10 out of 10. this ball is a great medium-heavy oil ball.

Jason R Stacy

  • Jr. Member
  • **
  • Posts: 7
Re: Eraser Boost
« Reply #22 on: September 10, 2002, 02:26:29 PM »
Well I got this ball last wednesday with a 4in pin and 3 oz of top weight.Had it drilled for max hook.This is the FREAKIEST ball ever!!!I was bowling with it on lanes oiled 10 to 10 36ft.If i bowled anywhere outside 10 the darn thing hooked like hell.But when I threw it in the oil it went strait as an arrow.So threw it across the oil on board 15 it slid out to 5 and came roaring back and just crushed the pins.I only bowled a 506 but was playing a whole different line than I was used to.Now last night was a diffrent story.I shot a 166(missed spare and 2 splits)214,213.And no tenpins at all.Will write another review tommorrw after my tuesday night league.


bowlman23

  • Jr. Member
  • **
  • Posts: 8
Re: Eraser Boost
« Reply #23 on: September 16, 2002, 12:07:04 AM »
I just got this ball last Tuesday drilled stacked with the pin located above the bridge.  Kept the cover from the out of the box, and tried it out.  What I found was a ball that was consistent, and predictable.  I throw around medium revs, usually down and in, but can move in and swing the ball.  I was standing about 30, throwing the ball to 23 bellying all the way out to 8 and the ball conserved energy and exploded on the backend, just demolishing the pins.  I was shocked at how much backend the ball had.  I noticed I pulled a couple shots, and the ball held the oil all the way down, which is unusual these days because most balls roll so early, they hook right through the oil.  I've used this ball on several conditions and have found a shot on every one.  The ball adjusts well to dry lanes, if you have the speed to throw the ball to your breaking point.  I tried the ball on very tight lanes, and I must say it didn't react no where near as strong as it did previously, but the ball isn't designed to handle that.  Even though it didn't react as strong, I just moved outside and pointed the ball up to the pocket, and it maintained its hitting power.  All in all, Storm has designed yet another winner, and this will be the benchmark ball in my bowling arsenal.  Good overall ball, for not a lot of money.  Now a days, it seems like most manufacturers are trying to make balls that hook more and more, but let's be honest.  How many people really bowl on heavy oil conditions?  Not many!  Most league bowlers bowl on a condition that is medium lane oil with mild backends.  All these super-soft coverstocks are for the most part too aggressive, and that's why I like this ball because it is a good mid-lane ball.  Bottom line, it's worth the money, and the ball is versatile.  What else do you want in a ball?

CaughtbySTORM

  • Jr. Member
  • **
  • Posts: 14
Re: Eraser Boost
« Reply #24 on: October 01, 2002, 12:57:43 PM »
I LOVE this ball.  However it's drilled, it has nice length on most conditions, and a strong arcing backend, it doesn't set up and snap, it continues through the pins.  Nice smooth roll, even on wood lanes with dry backends.  It's very consistent, and especially for the price, you won't find a better ball for the price.  On most lane conditions, it'll be the ball you use before going to the higher performace of the Trauma line when the lanes start to break down.  But it's a nice enough ball that if you have a nice shot, you shouldn't need anything else.

BrianN

  • Jr. Member
  • **
  • Posts: 25
Re: Eraser Boost
« Reply #25 on: October 06, 2002, 10:21:11 AM »
Laid out 4 x 3, exactly 1 oz side (would probably have wanted to pop a tiny weight hole before going to tournament, just in case), 3/16 finger, 7/8 top. Almost needed a weight hole.

This is a post-mortem review. I tried hard, but failed to find any particular merit to this ball. I could never make it work on any of my 3 completely distinct shots, so I've already traded it away. It was a huge disappointment.

The positives: The Boost is reasonably smooth, with decent carry and the backend behavior was very responsive to my release. The backend was decently mellow, a good compromise between flippy resins and early rolling particles.

The negatives: My first criticism of the ball is that Storm falsely markets it as a big oiler. Their reaction chart indicates that it's for Long Medium, Medium Heavy and Short Heavy conditions. I bought it for a medium length (38') heavy (65 units, 8 outside) shot and it wasn't enough ball by a handful.

We took the surface down to 600, brought it back with Track Magic and tried again. Even after that, it's still not as strong as a Spirit, and not half the ball as far as breakpoint consistency, controllability and hit. I can't use a Spirit on this shot either.

Frankly, I don't understand what I could use Boost for. If I had a very clean, forgiving light to light-medium league shot on wood (i.e., not too much carrydown) without too much oil in the heads, it might be a second choice behind my 3-piece. Here, by 'light', I'm talking about 30 - 35 units.

People talk about Columbia coverstocks being squirty - whenever I put Boost on wet heads, this coverstock always made the breakpoint an adventure.

I can't give it more than a 7, composed of the following:

Control: 7. Good backend behavior not outweighed by squirtiness.

Versatility: 6. Not a clue what this thing was intended for. I couldn't find any use for it on 3 vastly different shots.

Carry: 8. Decent hitting ball. I have 3-pieces that are better, though.
The budget should be balanced, the treasury refilled, public debt reduced, the arrogance of officialdom tempered and controlled, and the assistance to foreign lands curtailed, lest Rome become bankrupt.  
 
-- Cicero, Roman statesman

A Maverick

  • Newbie
  • *
  • Posts: 4
Re: Eraser Boost
« Reply #26 on: October 20, 2002, 12:11:08 PM »
Hi All,

   Now that I have quite a few games on this ball, I wanted to refresh my review for this ball.  I'm going to buy another one and keep it in the closet to replace the existing whenever, if ever, it tracks out.  I have this ball in the standard Storm #3 drilling.  It took about 15 games to break it in and I've rolled at least 200 games with it so far.  I have done nothing to the cover stock since I bought it except one time I put it in a polisher when it was getting to strong of a early roll and I clean it every night.  I use it on four different leagues and it is now the only ball I use for all conditions except very heavy oil with short backends.  On these rare occasions, I break out my Response.  Finally, I don't need a cart to carry enough balls to handle different oil conditions.  I even use it consistently for 10 tens.




biteme_2010

  • Newbie
  • *
  • Posts: 1
Re: Eraser Boost
« Reply #27 on: November 01, 2002, 03:51:14 PM »
this ball smells

cocamidoproply

  • Jr. Member
  • **
  • Posts: 11
Re: Eraser Boost
« Reply #28 on: November 23, 2002, 05:38:10 PM »
This is by FAR one of the worst bowling balls I have ever thrown. It does, granted, get exceptional length, and then i wait for the BOOSTED recovery....It doesn't come.  And when I play it up the middle, it hits with the most horible power.  I think a dead leaf blown by a 2 MPH wind would hit harder.  The pin is above the ring finger, and CG in the palm.  Terrible, but who knows, maybe it is just the "S" on it that makes it not do good... Perhaps it should be replaced with an AMF logo, then they may actually produced a good ball.



I need ignorant people like i need an inoperable tumor at the base of my spine.  


CarneyJosh

  • Newbie
  • *
  • Posts: 3
Re: Eraser Boost
« Reply #29 on: November 26, 2002, 10:42:35 PM »
This Ball Is GREAT. It is one of the most versititle ball out there in my opinion. you can swing it or play down and in and it will work either way. This ball is another great one from storm, AMF SUX byt the way.

StrikeMonster

  • Sr. Member
  • ****
  • Posts: 274
Re: Eraser Boost
« Reply #30 on: November 27, 2002, 09:54:44 AM »
I've had this one for a couple of months now.  I've used it on a variety of conditions and oil volumes (fresh synthetic, fresh wood, 2nd shift synthetic, 3rd shift wood, sport)and have had great success with it on all the conditions, I've tried.  It works great going up the boards, playing tight inside or swingin out from deep inside.  This ball rolls so smooooothly.  
The pin is 2" and under ring finger with CG under my palm.
I love this ball, another great one from Storm