-
How do these compare to each other?
I have a 715T drilled 65x4.5x30 as my heaviest oil ball, Im thinking about getting another ball before Reno....
How would these fit in my arsenal?
My Current Arsenal:
715T................... 65x4.4x30 1000AB
505T................... 65x4.5x30 2000AB
Bank Pearl...........60x5x40 1500 polished
Dark Star.............70x3.5x40 1500 polished
Red Backlash.......80x3x40 2000 polished
-
If you aren't against plugging your equipment I would move the pin down on your 715T and drill up a Nano with your current 715T layout. It will give you two different heavy oil looks.
-
Yes think about pin positions on your layouts...pin up, pin even and pin down factoring in pin to PAP distances.. I think this would have alleviated your issue with the 607A SE if you would have gone pin down.
I'd definitely see the Nano in strength above the 715T.
I wondered why all your VAL angles are so acute? Does this relate to your stats.?
Scott
-
All of these drillings were recommended by my proshop. I do not know all my stats...My PAP is 5 1/8th over and 1 up......15-16mph...350-375 not sure of tilt, axis between 45 and 60 I think. My proshop says I need help getting the ball through the heads, that is why the 60+ drilling angles, he also told me around 100 total angles +/-20. Since he has been drilling my stuff I have felt more comfortable reading what the ball will do, except for the 607A.. When I need the ball to read a bit earlier, I take the surface down a bit.
I have only had two balls pin down in my whole bowling career, A Cell and a Street Rod Pearl, both balls rolled up too early, even the SRP. So I had both redrilled pin up and had success with both.
I am just learning about drilling patterns after all these years. I always banked on my proshop to set me up a ball that would nfit what I wanted/needed.
I average 210ish just about anywhere and when i struggle its usually with my timing more than anything else. I did avg 218+ for a few years back in the mid 90's, then i quit for over 10 yrs. I just started bowling again in the beginning of last bowling season
My Current Arsenal:
715T................... 65x4.4x30 1000AB
505T................... 65x4.5x30 2000AB
Bank Pearl...........60x5x40 1500 polished
Dark Star.............70x3.5x40 1500 polished
Red Backlash.......80x3x40 2000 polished
-
All of these drillings were recommended by my proshop. I do not know all my stats...My PAP is 5 1/8th over and 1 up......15-16mph...350-375 not sure of tilt, axis between 45 and 60 I think. My proshop says I need help getting the ball through the heads, that is why the 60+ drilling angles, he also told me around 100 total angles +/-20. Since he has been drilling my stuff I have felt more comfortable reading what the ball will do, except for the 607A.. When I need the ball to read a bit earlier, I take the surface down a bit.
I have only had two balls pin down in my whole bowling career, A Cell and a Street Rod Pearl, both balls rolled up too early, even the SRP. So I had both redrilled pin up and had success with both.
I am just learning about drilling patterns after all these years. I always banked on my proshop to set me up a ball that would nfit what I wanted/needed.
I average 210ish just about anywhere and when i struggle its usually with my timing more than anything else. I did avg 218+ for a few years back in the mid 90's, then i quit for over 10 yrs. I just started bowling again in the beginning of last bowling season
My Current Arsenal:
715T................... 65x4.4x30 1000AB
505T................... 65x4.5x30 2000AB
Bank Pearl...........60x5x40 1500 polished
Dark Star.............70x3.5x40 1500 polished
Red Backlash.......80x3x40 2000 polished