win a ball from Bowling.com

Author Topic: need urethane hammers  (Read 3075 times)

armswing

  • Sr. Member
  • ****
  • Posts: 484
need urethane hammers
« on: December 16, 2007, 11:58:41 AM »
Need faball powder blue hammer in 15lb. need pink urethane hammer in 14lb. I will be checking post daily thanks.

 

abrown

  • Hero Member
  • *****
  • Posts: 1030
Re: need urethane hammers
« Reply #1 on: December 16, 2007, 08:03:52 PM »
have a old burgany hammer setting at the pro shop 15 lbs

armswing

  • Sr. Member
  • ****
  • Posts: 484
Re: need urethane hammers
« Reply #2 on: December 18, 2007, 10:42:56 AM »
quote:
have a old burgany hammer setting at the pro shop 15 lbs

armswing

  • Sr. Member
  • ****
  • Posts: 484
Re: need urethane hammers
« Reply #3 on: December 18, 2007, 10:45:56 AM »
Hello A BROWN how is the condition of the purple 15lb urethane hammer? And how could iI see it and get my hand on it?

RandyO

  • Hero Member
  • *****
  • Posts: 1213
Re: need urethane hammers
« Reply #4 on: December 18, 2007, 02:12:13 PM »
Be careful. A burgundy hammer is NOT a purple hammer. In my experience, the Burgundy was the worst. It chipped very easily, and the reaction was the worst of all of the urethane hammers. I really liked the Purple urethane hammer - definitely NOT the same as a burgundy.

charlest

  • Hero Member
  • *****
  • Posts: 24523
Re: need urethane hammers
« Reply #5 on: December 18, 2007, 05:04:30 PM »
quote:
Be careful. A burgundy hammer is NOT a purple hammer. In my experience, the Burgundy was the worst. It chipped very easily, and the reaction was the worst of all of the urethane hammers. I really liked the Purple urethane hammer - definitely NOT the same as a burgundy.


Oddly you go against the VAST majority with respect to the Burgundy Hammer. Maybe you have/had too many revs for it and needed the Purple??  I don't know for sure. Was the purple weaker than the Burgundy or vice-versa?

I have seen more Burgundy hammers in the past 5 years than I saw in all of 1992 - 1996, its prime.
--------------------
"None are so blind as those who will not see."
Unofficial Ballreviews.com FAQ

Edited on 12/18/2007 6:14 PM
"None are so blind as those who will not see."

bluerrpilot

  • Hero Member
  • *****
  • Posts: 1235
Re: need urethane hammers
« Reply #6 on: December 18, 2007, 05:20:48 PM »
quote:
I don't know for sure. Was the purple weaker than the Burgundy or vice-versa?




The burgandy was the strongest of the urethane Hammers.
--------------------
Team HammerHead
2008 USBC Nationals
ABQ, NM


http://forums.hammerbowling.com
http://www.azbowlersclub.net
http://www.azbowling.com


Edited on 12/18/2007 6:21 PM

charlest

  • Hero Member
  • *****
  • Posts: 24523
Re: need urethane hammers
« Reply #7 on: December 18, 2007, 08:17:52 PM »
So Randy probably needed the weaker ball because he is a stronger bowler than average. OK.
--------------------
"None are so blind as those who will not see."
Unofficial Ballreviews.com FAQ
"None are so blind as those who will not see."

RandyO

  • Hero Member
  • *****
  • Posts: 1213
Re: need urethane hammers
« Reply #8 on: December 18, 2007, 11:35:09 PM »
The Purple was similar to the Blue except that it was a bit "longer". Blue was a bit more arcy. I bought two burgundy hammers. First one had a chunk come flying out when it was being drilled. A major 2 inch chunk during the drilling of the FIRST finger hole.
The second one didn't crack / chip until a bit later. My main problem was that the reaction wasn't consistent. That may have been "house" specific in that there may not have been sufficient oil volume to warrant its usage. However, it quickly became chipped, around the fingers. Finally developed some cracking, and I dumped it. I never had a bad experience with Black, Blue, or Purple hammers - all of them were top-notch balls. The Red Razor urethane which was released in '95 was a MONSTER, but was overshadowed by all of the reactive balls. Faball urethanes were the BEST (except for the Burgundy - IMHO). I am not nor was not ever a hi-rev bowler. Tweener at best.

ten pin killler

  • Sr. Member
  • ****
  • Posts: 310
Re: need urethane hammers
« Reply #9 on: December 19, 2007, 04:25:27 AM »
I shot my first 700 with a burgundy back in the early 90's. I never had an issue with it and ended up selling it to a buddy that still has it to this day.......great ball!!!!!!!
--------------------
TPK .... A HammerHead with a touch of BuzzSaw

Nothing hits like a Hammer!!!!

Could someone tell me where this "Great Wall of China" is???