win a ball from Bowling.com

Author Topic: yet another Cobalt question  (Read 795 times)

Big Jake

  • Hero Member
  • *****
  • Posts: 1745
yet another Cobalt question
« on: March 29, 2006, 01:42:20 PM »
Hello Group,
 Second post here, so again 'Hello All', here's my question.

I am getting my first LANE#1 tomorrow or possibly on Friday (the Cobalt) and I am still trying to decide what drill pattern that I would go for.

So could someone be kind enough to explain to me the difference between 'Flare' and 'Backend'.

The reason is I'm looking at the drill sheet for the Cobalt (from LANE#1 site) and apparently this ball seems to have a lot of backend no matter how its drilled.

Label Stacked:
--------------
Flare = 9
backend = 9  

CG Out:
--------
Flare = 8
backend = 8

Neg Pin CG strong:
------------------
Flare = 3
backend = 8

------------------------------------------
      a little history here

Here is the reason I have picked out this particular ball. I just got the
 
1) Scorchin Inferno for heavy oil
2) Cobalt when Scorchin Inferno gets crazy
3) The One for when Cobalt goes crazy

I already had The One for about two months but my house where I bowl started using some real heavy oil patterns and so I got the Scorchin Inferno. So when

that one started to get to be kinda unusable I found that The One wouldn't set up in time due to some heavy carry-down so it keep coming in a little behind the headpin so I decided to get the Colbalt to be used when that happens.

Thanks for helping me out,
God Bless,

 SJ
Now throwing pretty much all flavors...

 

SprayNpray

  • Hero Member
  • *****
  • Posts: 726
Re: yet another Cobalt question
« Reply #1 on: March 29, 2006, 11:52:28 PM »
In my opinion, you should use the One after the Scorchin, then the Cobalt.  The Cobalt is not going to like carry down much at all, and skates in oil.  It does have a sick backend, though, so it will help with entry angle.  I guess if you keep your line far outside and let the ball start up before it hits carry down, it will have a chance.

Flare in my terms describes how far apart the oil rings on the ball are, hence how much does the axis of rotation migrate as the ball travels down the lane.  More flare means that it is more likely that a fresh part of the ball is in contact with the lane surface on every revolution.  The oil rings will be farther apart the more a ball flares.

It is actually possible for a ball to over flare and have a negative effect on the reaction you get, causing the ball to cover FEWER boards.

Backend depends on the context.  Obviously it is the end of the lane nearest the pins, where there is usually little or no oil.  The ball uses this part of the lane to create friction and therefore hook.  Some balls are designed to roll early (in the front part of the lane), others, like the Cobalt, are designed to skid in oil and grab hard on the backend, creating entry angle.

That is my rudimentary explanation; I'm sure someone else can put it more eloquently than I did.
--------------------
Predicting my next opponent runs into a BUZZSAW!

Member- FOS

LUCK is what happens when preparation meets opportunity.

T-GOD

  • Hero Member
  • *****
  • Posts: 2141
Re: yet another Cobalt question
« Reply #2 on: March 30, 2006, 09:23:15 AM »
saint, you don't say how you have your oter balls drilled or how you throw the ball, including what your axis dimensions are and what your rev rate is. This makes it difficult to recommend a layout.

In general, for higher rev rates, I would keep the pin around your center line, either just under or just over the bridge, while kicking the CG out between 1 - 2".

For lower rev rates, a stacked drilling with pin around the ring finger should work well.

Lane 1 balls work on the KISS philosophy, Keep It Simple Stupid. KISS your Lane #1 balls and they'll will work just fine..!! =:^D