win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: 2 3/4 top and 1 inch pin, help!  (Read 607 times)

splitcity

  • Sr. Member
  • ****
  • Posts: 398
2 3/4 top and 1 inch pin, help!
« on: September 01, 2006, 02:27:06 PM »
is this a good combination? i have a ball with these specs and dont know if i got trouble or good specs. any advice?
Logged
lets face it... this isnt deadlifting or picking up women.. its BOWLING!!!! Stop acting tough when you roll 4 strikes in a row!!!

 

monstercrank

  • Hero Member
  • *****
  • Posts: 1867
Re: 2 3/4 top and 1 inch pin, help!
« Reply #1 on: September 01, 2006, 10:27:46 PM »
well its not bad specs....
--------------------
"I don't like country music, but I don't mean to denigrate those who do. And for the people who like country music, denigrate means 'put down'" - Bob Newhart

---------------------------------
If guns kill people then spoons made Rosie O'Donnell fat!
-----------------------------
Some people are like Slinkies....
Not really good for anything, but they still bring a smile
to your face... when you push one down a flight of stairs.
Logged

triggerman

  • Hero Member
  • *****
  • Posts: 3352
Re: 2 3/4 top and 1 inch pin, help!
« Reply #2 on: September 01, 2006, 10:34:50 PM »
quote:
is this a good combination? i have a ball with these specs and dont know if i got trouble or good specs. any advice?


what kind of ball and what do you wnat it to do.  those questions will determine how limited you are on the drilling, not bad specs for certain drillings
Logged

splitcity

  • Sr. Member
  • ****
  • Posts: 398
Re: 2 3/4 top and 1 inch pin, help!
« Reply #3 on: September 02, 2006, 08:32:47 AM »
a columbia bully. i want max hook and late flip
Logged
lets face it... this isnt deadlifting or picking up women.. its BOWLING!!!! Stop acting tough when you roll 4 strikes in a row!!!

shelley

  • Hero Member
  • *****
  • Posts: 9655
Re: 2 3/4 top and 1 inch pin, help!
« Reply #4 on: September 02, 2006, 02:00:19 PM »
In that case, you're probably looking at putting the pin fairly high above the midline, even with or above the fingers.  With that 1" pin, you'll have a lot of finger weight.  You can either remove it with a weight hole in the positive finger quadrant or drill the fingers slightly deeper.  It's not the ideal ball for that reaction, but it should work just fine.

SH
Logged

jls

  • Hero Member
  • *****
  • Posts: 18398
Re: 2 3/4 top and 1 inch pin, help!
« Reply #5 on: September 02, 2006, 02:05:48 PM »
sounds like you have apin in.
have it drilled pin in line with your pap and ring finger.
than a bal hole will be needed.  about 1 1/2 down from you pap.
and the finger holes may also need to be drilled a little deeper.
--------------------
jls31316
Logged

kmanestor22

  • Hero Member
  • *****
  • Posts: 969
Re: 2 3/4 top and 1 inch pin, help!
« Reply #6 on: September 02, 2006, 02:27:05 PM »
Drill it pin 3-3/8" from PAP, cg kicked 45 degrees.  Double drill your ring finger deep and see what you have.  If there is still too much finger weight, double drill the other finger.  Add a weight hole if needed.
--------------------
Where is the bait?  I'm goin' to jail!!! - Chocolate GAYzer
Logged

splitcity

  • Sr. Member
  • ****
  • Posts: 398
Re: 2 3/4 top and 1 inch pin, help!
« Reply #7 on: September 02, 2006, 02:30:48 PM »
thanks guys
Logged
lets face it... this isnt deadlifting or picking up women.. its BOWLING!!!! Stop acting tough when you roll 4 strikes in a row!!!
Pages: [1]
« previous next »