win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: My Ravage arrived today.....woooooohooooo  (Read 1486 times)

agroves

  • Hero Member
  • *****
  • Posts: 4939
My Ravage arrived today.....woooooohooooo
« on: May 14, 2004, 10:41:01 AM »
I went to the shop today to drop off my new/used Time Zone for plugging.  I looked on the floor and what did I see?  My new Ravage.  I have to admit it looks pretty cool.  I believe it was a 3 inch pin out.

Now the question of the day:

How should I drill it?  I can tell you this, it won't be high flare.  I was thinking about the Forward roll or Control layout.  Please feel free to provide suggestions.  Specs in profile.

andrew
--------------------
FUFU
If you're an idiot, you can join my ignore list
Logged

 

agroves

  • Hero Member
  • *****
  • Posts: 4939
Re: My Ravage arrived today.....woooooohooooo
« Reply #1 on: May 15, 2004, 01:47:37 AM »
smart *ass*!!!!  Never thought of that, I will have to give it a try.

andrew
--------------------
FUFU
If you're an idiot, you can join my ignore list
Logged

MoRich

  • Jr. Member
  • **
  • Posts: 41
Re: My Ravage arrived today.....woooooohooooo
« Reply #2 on: May 15, 2004, 07:57:14 AM »
I would agree with the forward roll control drilling for you.  I would put the pin around 2 1/2" from you PAP and the mass bias in the neighborhood of 6".  Keep the pin somewhat low (about 1" above the mid line).  This will give you the look I think you want.  Realize when you take flare out the balls, you will lose a little of the area that can be created by the ball.  I actually drilled one up just the way I am suggesting to you and one with a lot of flare.  The two complement each other very well.  I know I was going to PM you this stuff, but I thought this seemed easier.  PM or post if you have any other questions.  Thank you very much for the support.
--------------------
www.morichbowling.com
Logged

chun914

  • Sr. Member
  • ****
  • Posts: 256
Re: My Ravage arrived today.....woooooohooooo
« Reply #3 on: May 16, 2004, 04:02:02 AM »
why always a 2 1/2 pin to pap ???
Logged

charlest

  • Hero Member
  • *****
  • Posts: 24523
Re: My Ravage arrived today.....woooooohooooo
« Reply #4 on: May 16, 2004, 07:43:24 AM »
quote:
Now the question of the day:

How should I drill it?  I can tell you this, it won't be high flare.  I was thinking about the Forward roll or Control layout.

andrew
--------------------
FUFU
If you're an idiot, you can join my ignore list


Since it's a Morich core and you don't want high flare (check this out, chun!), you have no choice but to put the pin in the neighborhood of 2-3" from your PAP.
Morich's cores, as stated by Mo himself, will flare a lot in either standard strong pin positions of 3.5-4" from your PAP and in what are normally long pin (low flare) positions of 4.5-5.5" from your PAP. This seems to a property of his core designs.

This would seem to leave you ONLY with a choice of where to locate the MB, 3-4" from the VAL or 5-6" from the VAL.


--------------------
"We get old too fast, and too late, smart."


Edited on 5/16/2004 7:41 AM
Logged
"None are so blind as those who will not see."

chun914

  • Sr. Member
  • ****
  • Posts: 256
Re: My Ravage arrived today.....woooooohooooo
« Reply #5 on: May 16, 2004, 08:02:21 AM »
is it a disavantage to have high flare on Morich's core ??
Logged

charlest

  • Hero Member
  • *****
  • Posts: 24523
Re: My Ravage arrived today.....woooooohooooo
« Reply #6 on: May 16, 2004, 09:18:12 AM »
quote:
is it a disavantage to have high flare on Morich's core ??


not at all; my point was that Andrew (agroves) wanted a low flare drilling and
I am fairly certain that is why Morich suggested the 2 1/2" pin position.

See Morich's website; he has 3 basic drillings for each ball, 2 of which are control (2-3" pin position), sharp break (3.5-4", more or less, pin position), which we often refer to as "Stacked Leverage" in symmetric balls,.
--------------------
"We get old too fast, and too late, smart."
Logged
"None are so blind as those who will not see."
Pages: [1]
« previous next »