win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: Need suggestion on how to drill a Virtual Gravity.  (Read 1110 times)

The Syrup

  • Jr. Member
  • **
  • Posts: 32
Need suggestion on how to drill a Virtual Gravity.
« on: March 06, 2010, 06:50:21 PM »
Just bought a used VG, plugged. Not sure how to drill it. Unfortunatley I dont know my PAP...so looking for a "safe" way to drill.
Ball has a 3" pin..top not known.
About me, stroker, med revs about 275 I would guess, med/slow speed.
Would like to get decent length, (due to slowish speed) with an arcing controlable backend reaction.
Thanks in advance for your help guys.
Logged

 

srlunatic

  • Hero Member
  • *****
  • Posts: 4316
Re: Need suggestion on how to drill a Virtual Gravity.
« Reply #1 on: March 07, 2010, 06:38:10 AM »
Greetings...

Without knowing specifics but knowing what you are looking for in reaction...

Would suggest this...


Pin up means length...I like pin above my bridge for length. Don't be afraid to go higher if needed.  If really are slower than most do not be afraid to put it an inch to an inch an 1/2 above your bridge.

Arcing means you want the Mass Bias out away from your thumb and near your Vertical Axis.  Would say that is you go 3 to 3 1/2 inches right or left of your thumb (right if a righty, left if a lefty) then you should get arc.

Again this is just a general layout but should give you close to what you are looking for.

Hope this helps!

Mike
--------------------
They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety.
Logged
They that can give up essential liberty to obtain a little temporary safety deserve neither liberty nor safety.

Jesse James

  • Hero Member
  • *****
  • Posts: 3605
Re: Need suggestion on how to drill a Virtual Gravity.
« Reply #2 on: March 07, 2010, 05:49:22 PM »
I have one of these. I am a slow speed stroker, between 15-16 mph. Med revs.
 
The surface change you put on this ball makes all the difference in the world. Dullish makes this ball an oil monster. Shiny allows you more versatility, but, how you drill it will ultimately determine when you can use it successfully.

I have seen people use this ball sucessfully shined up, on medium conditions, but most of those people throw around 17mph, or higher.

I drilled mine Rico, and can safely use it on all conditions.The only aspect that I change on oily conditions is the surface. This drilling gives me a controlled arc......in the back part of the lane.
--------------------
Duct tape is like 'The Force'. It has a light side and a dark side, but it still holds the universe together.

Some days you're the bug some days you're the windshield.
Logged
Some days you're the bug....some days you're the windshield...that's bowling!

The Syrup

  • Jr. Member
  • **
  • Posts: 32
Re: Need suggestion on how to drill a Virtual Gravity.
« Reply #3 on: March 07, 2010, 07:12:23 PM »
quote:
I drilled mine Rico, and can safely use it on all conditions.The only aspect that I change on oily conditions is the surface. This drilling gives me a controlled arc


Jesse... Im a high tracker, is this drill likley to clip any holes for me?
Logged

Jesse James

  • Hero Member
  • *****
  • Posts: 3605
Re: Need suggestion on how to drill a Virtual Gravity.
« Reply #4 on: March 08, 2010, 08:23:59 AM »
Not that I can see. I am a high tracker also, and this has never been a problem at all.
--------------------
Duct tape is like 'The Force'. It has a light side and a dark side, but it still holds the universe together.

Some days you're the bug some days you're the windshield.
Logged
Some days you're the bug....some days you're the windshield...that's bowling!

x1a4

  • Jr. Member
  • **
  • Posts: 79
Re: Need suggestion on how to drill a Virtual Gravity.
« Reply #5 on: March 08, 2010, 11:11:38 AM »
if you are worried about clipping just move the pin up an inch above the midline.
--------------------
Zoltan!
Logged
Pages: [1]
« previous next »