win a ball from Bowling.com
« previous next »
Pages: [1]

Author Topic: G 3 Drilling Ideas  (Read 1305 times)

pnj1967

  • Hero Member
  • *****
  • Posts: 3633
G 3 Drilling Ideas
« on: September 06, 2007, 09:56:33 AM »
Just found out I am going to be getting  G 3 next week ( a friend ) put my name in for a drawing and I won.

 I will be bowling on a THS this year (38 ft.) and most of the time clean back ends may, see some carry down once in a while.
 
PAP 4 1/4   1/8^
Lower rev rate
15-16 mph
Low axis rotation

Am looking for some thing with a skid/snap, and "maybe" once in a while to get through some carry down.

 Message me or leave idea here.

Looking for ideas for drilling.  Thanks

Ball  specs are 15.05, TW 3.46, Pin 2-3
--------------------
Enjoy the people on the ballreview.com forum. Like to help when I can.


Users I wont deal with, read my profile.













Edited on 9/10/2007 6:05 AM
Logged






 

Bar5003

  • Hero Member
  • *****
  • Posts: 1627
Re: G 3 Drilling Ideas
« Reply #1 on: September 06, 2007, 09:28:01 PM »
Check out my video for the G-3 on my website...one of the shots i throw on is a 38' ths...hope that helps!
--------------------
~Britton~

Owner and Operator of

www.videoballreviews.com

VISE inserts The OFFICAL grip of videoballreviews.com

www.viseinserts.com
Logged

dizzyfugu

  • Hero Member
  • *****
  • Posts: 7606
Re: G 3 Drilling Ideas
« Reply #2 on: September 07, 2007, 03:00:45 AM »
Skid/Snap and carrydown at the same time do not get together well...
Just like Drrev mentions: check the pin distance, and (less important) the top weight. For a snappy ball make sure to get a 3-4" pin, so you can have the pin set high, above the fingers.

The Gryphon core is IMHO pretty rolly, but has a huge potential because it is so simply. With a length layout, pin set above ring finger (say 4-4.5" from PAP) and CG stacked, you should get a good compromise between snap and carrydown capability. But for a true carrydown ball I'd rather suggest a pin-under-fingers layout with a shorter pin distance (1-2"), CG stacked or slightly swung out towards PAP.

Hope this helps a bit, too?
--------------------
DizzyFugu - Reporting from Germany

Confused by bowling?
Check out BR.com's vault of wisdom: the unofficial FAQ section
Logged
DizzyFugu ~ Reporting from Germany

pnj1967

  • Hero Member
  • *****
  • Posts: 3633
Re: G 3 Drilling Ideas
« Reply #3 on: September 07, 2007, 05:47:36 AM »
Ok guys I will post when I get the ball, what TW and Pin is that I get.

 The only reason I posted once in a while about the carry down is, I wanted to try and get the best recommendation.

 Paul


quote:
Skid/Snap and carrydown at the same time do not get together well...
Just like Drrev mentions: check the pin distance, and (less important) the top weight. For a snappy ball make sure to get a 3-4" pin, so you can have the pin set high, above the fingers.

The Gryphon core is IMHO pretty rolly, but has a huge potential because it is so simply. With a length layout, pin set above ring finger (say 4-4.5" from PAP) and CG stacked, you should get a good compromise between snap and carrydown capability. But for a true carrydown ball I'd rather suggest a pin-under-fingers layout with a shorter pin distance (1-2"), CG stacked or slightly swung out towards PAP.

Hope this helps a bit, too?
--------------------
DizzyFugu - Reporting from Germany

Confused by bowling?
Check out BR.com's vault of wisdom: the unofficial FAQ section

--------------------
Enjoy the people on the ballreview.com forum. Like to help when I can.


Users I wont deal with, read my profile.






Logged






pnj1967

  • Hero Member
  • *****
  • Posts: 3633
Re: G 3 Drilling Ideas
« Reply #4 on: September 08, 2007, 10:18:55 AM »
Ball came today.

 Specs are 15.05, TW 3.46, Pin 2-3 .
--------------------
Enjoy the people on the ballreview.com forum. Like to help when I can.


Users I wont deal with, read my profile.






Logged






TWOHAND834

  • Hero Member
  • *****
  • Posts: 4347
Re: G 3 Drilling Ideas
« Reply #5 on: September 08, 2007, 02:28:25 PM »
With those specs, I would do a drilling where the pin is under the middle finger (4 3/8 - 4 1/2 pin to PAP) with the CG kicked out just far enough to put a small weight hole in the thumb positive quadrant.  This should give you some earlier midlane read and yet still have some pop on the backend.  The key is to get the ball rolling before it gets to the carrydown.
--------------------
Steven Vance
Former Pro Shop Operator

If anyone out there is worried about the scores being too high, try duckpin!!
Logged
Steven Vance
Former Pro Shop Operator
Former Classic Products Assistant Manager

pnj1967

  • Hero Member
  • *****
  • Posts: 3633
Re: G 3 Drilling Ideas
« Reply #6 on: September 10, 2007, 06:06:38 AM »
Thanks TWOHAND834, any other ideas ?

--------------------
Enjoy the people on the ballreview.com forum. Like to help when I can.


Users I wont deal with, read my profile.






Logged






mrbowlingnut

  • Hero Member
  • *****
  • Posts: 5727
Re: G 3 Drilling Ideas
« Reply #7 on: September 10, 2007, 11:14:51 AM »
I like the twohand idea without a weight hole unless needed, having two of these you will find it works best on fresher medium's. Ok carrydown ball from the strong rolly core, i rarely see skid/snap from this ball but mine are both pin under ring drillings.
Logged

VBPadvertising

  • Full Member
  • ***
  • Posts: 245
Re: G 3 Drilling Ideas
« Reply #8 on: September 10, 2007, 03:03:35 PM »
Hey pnj1967,

Just wanted to say congratulations on the drawing, and wish you luck with the ball.  Bowl well!

Jason Wonders
Visionary Bowling Products
Logged
Pages: [1]
« previous next »